Tp Link Wireless For Mac

Posted on by



  • 5.After MAC is rebooted, please click the Wi-Fi icon to “Open Wireless Utility”, then you can choose your Wi-Fi and connect it. (Note: it may take time for utility to search W i-Fi, please wait patiently for about 1 min.) Now please enjoy your W i-Fi.
  • TP-Link AC1200 Gigabit Smart WiFi Router - 5GHz Gigabit Dual Band MU-MIMO Wireless Internet Router, Supports Beamforming, Guest WiFi and AP mode, Long Range Coverage by 4 Antennas(Archer A6), Black TP-Link AC1900 Smart WiFi Router - High Speed MU- MIMO Wireless Router, Dual Band, Gigabit, VPN Server, Beamforming, Smart Connect, Works with Alexa.

Dear All,

TP Link - Download Center. Download Center. For firmware, drivers, user guide, utility or any other download resources, please select the product model number through the search engine or the tab list.

Hereby, I want to share a solution for an issue I had with my new Archer C9.

The Set-up

- ISP Modem (LAN 192.168.0.1) - Ethernet LAN Port 1 to

- Access Point A (TP-Link Archer C8) - Static LAN 192.168.0.2 - DHCP Disabled - Connected through Ethernet LAN Port 1

- Access Point B (TP-Link Archer C8) - Static LAN 192.168.0.3 - DHCP Disabled - Connected through Ethernet LAN Port 1

- Access Point C (TP-Link Archer C9) - Static LAN 192.168.0.4 - DHCP Disabled - Connected through Ethernet LAN Port 1

Mac

All carry out the same SSID

The Issue

- For AP A and B (both C8), the settings work fine by disabling the DHCP and connecting through Lan Port 1

- For AP C (the C9), the exact same setting did not work - the wired clients have LAN/WAN access, the wireless clients only have LAN access.

- 'Access Point Mode' does not allow 'Router Mode' options (such as NAT, QoS, MAC Filtering, ..)

The combination 'same SSID' - 'Access Point Mode' + clients always choosing the right Access Point is not guaranteed, since in my set-up, I had MAC filtered clients from AP B and C which always need to connect to AP A.

The Solution

Mac

A. If you are OK with having different SSIDs and do not need the extra Router Mode Options, you can easily run the Archer C9 in Access Point Mode - Done.

or

Tp Link Wireless Utility Mac Os

B. If you need some of the Router Mode Options, the key is to enable a WDS Bridge to the Ethernet MAC Address of the Router, since the wired clients do get a fully working connection.

Here are the steps to set it up:

1. Set-up the Archer C9 as an Access Point manually

- Go to 'Network - LAN'

- Enter the IP address manually within the subnet of the main router (e.g. 192.168.0.x)

- Enter the subnet mask identically as the subnet mask within the LAN (e.g. 255.255.255.0)

2. Set-up the Wireless Connections and SSID

Tp link wireless utility mac os

- Go to 'Wireless - Wireless Settings'

- Set-up your 2.4Ghz and 5Ghz SSID

3. Now, we need to bridge the LAN to your Wireless SSID

- Go to 'System Tools - System Parameters'

- Under '2.4Ghz Wireless', click 'Enable WDS Bridging'

- Now, enter the MAC Address of the LAN part to be bridged of the Archer C9 (can be found under 'Network - LAN')

4. Lastly, disable the DHCP server, as the DHCP settings will be received from the main router

Tp link wireless for mac os

Tp Link Wifi For Mac

- Go to 'Network - DHCP Server'

- Untick the box 'Enable DHCP Server'

Tp Link Wireless Card

5. Reboot the Access Point

6. Now, you should be able to access the LAN and WAN, both wired and wireless, and tweak the settings (such as MAC filtering) further!

Tp Wireless Wtg02

Tp link wireless adapter driver for mac

Hope this was useful.

Best regards,

kurgom86

Mac os for sony Mac OS® X version 10.9 - 10.13 IMPORTANT: For computers running Mac OS X version 10.13, the DriverLoader1013 software must be installed before installing the camera software update for each camera that's being updated. WARNING: This utility is only for use with the Sony® ILCE-5100 camera. Do not install this utility with any other model. Apple® Mac OS X® version 10.8 - 10.11. IMPORTANT: This update is not compatible with Mac OS X version 10.13. Apple® Mac OS X® versions 10.10 - 10.13 IMPORTANT: For computers running Mac OS X version 10.13, the DriverLoader1013 software must be installed before installing the camera software update for each camera that's being updated. Camera power supply: This update can only be performed when the remaining battery level has three bars or more.